The Select Series X300 Lawn Mowers from John Deere - maneuverability masters designed for homeowners who mow up to 3.5 acres and have varied terrain and light-to-moderate yard tasks. John Deere X300 Lawn Mower User Manual. Of 1 X300 with 42” Edge Deck. VIEW Technical (Service). I need a manual for model 1130SE john deere,how. What size is the roller chain drive for snow blowe.
1. Park vehicle safely. (See Parking Safely in Safety Section.) Allow engine and muffler to cool completely.
| c CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: · Disconnect spark plug wire(s) to prevent engine from starting accidently. · Always wear gloves when handling mower blades or working near blades. |
2. Adjust mower cutting height to 25 mm (1 in).
3. Put wood blocks under each side of mower.
| c CAUTION: Avoid injury! Lift lever is spring-assisted and may have unexpected movement. Put the lift lever in the mowing position before removing or installing the mower. |
4. Mac os x lion iso for vmware. Put lift lever in mowing position, bringing deck down onto blocks.
M88488
Picture Note: 38-Inch mower deck is used for photo purposes throughout this procedure.
5. Remove belt from engine drive sheave and belt guides (A).
MIF
6. Remove spring locking pin and washer (B) to remove adjustment link and engagement rod (C) from arm.
MX5364
7. Remove spring locking pin (H) and long drilled pin (G) from front of mower.
8. Remove front draft rod (E) from tractor bracket hole (D) first, then front mower bracket (F).
MX5363
9. Remove spring locking pin and drilled pin (I) from both rear draft arms (J) and mounting brackets.
10. Move lift lever to the transport position to raise rear draft arms.
11. Remove wood blocks from both sides and slide mower out from under the tractor.
1. Park vehicle safely. (See Parking Safely in Safety Section.) Allow engine and muffler to cool completely.
2. Check that mower cutting height knob is set at 25 mm (1 in).
3. Put lift lever in transport position.
| c CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: · Disconnect spark plug wire(s) to prevent engine from starting accidently. · Always wear gloves when handling mower blades or working near blades. |
4. Slide mower under the tractor.
5. Put wood blocks under each side of mower deck.
| c CAUTION: Avoid injury! Lift lever is spring-assisted and may have unexpected movement. Put the lift lever in the mowing position before removing or installing the mower. |
MX5363
6. Move lift lever to the mowing position to lower mower rear draft arms (A).
7. Fasten rear draft arms to mower mounting brackets with drilled pins and spring locking pins (B), on both sides of mower. Push spring locking pin all the way through as shown.
MX5364
8. Install front draft rod (E) into front mower bracket (F) first, then tractor bracket top hole (C). Make sure rounded bushing (D) is on front side of tractor bracket.
9. Install long drilled pin (G) and fasten with spring locking pin (H).
IMPORTANT: Avoid damage! The belt will be damaged if installed wrong. Route the belt properly through belt guides. |
M88482
10. Put mower drive belt on engine drive sheave (J). Make sure belt is routed through both belt guide loops (I).
MX5363
11. Check to make sure belt (K) is on all sheaves and idlers and is inside all belt guides (L).
12. Remove wood blocks from both sides of mower.
13. Move lift lever to mowing position and make sure mower engagement lever is pulled back into stop position.
14. Make sure mower is at lowest possible cutting height and that gauge wheels are not touching the ground.
IMPORTANT: Avoid damage! If the mower engagement rod is not adjusted properly, the mower belt may slip or drag on blade sheave resulting in belt damage. |
MIF M88502
15. Check to see if adjustment pin (P) lines up with mower engagement arm hole (O).
· If pin does not line up, loosen lock nut (Q) and turn pin until pin slips freely into hole. Tighten lock nut.
16. Fasten adjustment pin (P) to mower arm with washer and spring locking pin (M).
17. Level mower.
NOTE: In this procedure the mower deck is removed for easier access. However, it is NOT necessary to remove deck when replacing belt.
1. Park tractor safely. Allow engine and muffler to cool completely.
2. Remove mower if desired.
M88485
3. Remove three cap screws (A) and belt shield.
MIF
4. Loosen rear idler (B) and tensioning sheave (C).
5. Remove mower belt.
6. Clean top of mower.
7. Install new belt on mower as shown above.
8. Tighten rear idler and tensioning sheave.
9. Install belt shield and fasten with three cap screws.
10. Install mower deck and adjust mower engagement rod, if necessary.
1. Park machine safely. Allow engine and muffler to cool completely.
2. Remove mower.
MX5359
3. Remove self-tapping cap screws (C).
4. Move brake assembly (B) away from sheave (A) and drive belt.
5. Loosen idler (D) and tensioning idler (E) just enough to slip belt past the guides.
6. Remove drive belt and clean top of mower.
7. Install new belt on mower deck as shown.
8. Tighten idler (D) and tensioning idler (E).
9. Align brake assembly (B) with right spindle sheave (A) and fasten with self-tapping cap screws (C). Brake pad must seat against top of sheave.
10. Install mower and adjust mower engagement rod, if necessary.
1. Park machine safely.
2. Move lift lever to mowing position and move to left side of mower.
NOTE: Mower timing belt cover can be unfastened and flipped open on the left side, exposing the tension adjustment mechanism, without having to remove the mower or the timing belt cover.
MX5360
Picture Note: Mower removed for photo clarity.
3. Remove flange lock nut (A) to flip open left spindle cover.
MX5361
4. Check timing belt for damage. If the belt is damaged, replace the timing belt.
5. Remove top washer first, then loosen idler assembly center nut (B) ONE FULL TURN ONLY.
MX0238
6. Check that blades are timed properly (90° from each other). If blades are out of time, set blades to proper timing.
MX5361
7. Turn left spindle sprocket (C) to be sure belt is seated properly in the sprockets and idlers.
IMPORTANT: Avoid damage! Incorrect belt tensioning can cause belt damage. Do not over tighten belt tensioning spring assembly. |
8. Loosen jam nut (D) and adjusting nut (E) so that there is a small air gap between washer (F) and mating surface of spring bushing (G).
9. Rotate adjusting nut (E) clockwise until washer (F) makes solid contact with the mating surface of spring bushing (G).
10. Tighten idler assembly center nut (B) to 87 N·m (64 lb-ft.).
11. Tighten jam nut (D) against adjusting nut (E) to 27 N·m (20 lb-ft.).
12. Turn left spindle sprocket (C) to be sure belt is seated properly in the sprockets and idlers.
NOTE: The position of the drain holes in the spindle sheave (A) and the indentations in the timing sprocket (M) are in alignment with the mower blades (K) and (L).
MX0236
13. Check that blades are timed properly (90° from each other). If blades are out of time, set blades to proper timing.
14. Install top washer on top of center nut (B) and close left spindle cover.
15. Fasten cover with flange lock nut and tighten to 14 N·m (10 lb-ft.).
IMPORTANT: Avoid damage! Damage may occur to the belt or blades after a major blade impact: · Check blades for damage and timing. · Check the timing belt for damage and proper tensioning. |
1. Park machine safely. (See Parking Safely in the Safety Section.) Allow engine and muffler to cool completely.
2. Remove mower.
3. Remove mower drive belt.
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
4. Check blade bolt torque anytime mower is removed. Carefully hold blade with glove, use a hand torque wrench, and tighten bolt to 57 N·m 42 lb-ft.).
MX5358
5. Move spindle brake assembly (C) and mower engagement rod assembly (D) back to clear timing belt cover.
6. Remove five flange lock nuts (A) and cover (B).
MX0234
7. Turn jam nut (E) and adjusting nut (F) counterclockwise to end of threaded rod, and remove tensioning spring assembly.
MX3866
8. Remove center nut and washer (G) and move fixed idler assembly (H) close to the spindle sprocket. DO NOT loosen other idler assembly hardware.
9. Raise idler assembly upward as you carefully remove timing belt from the left spindle sprocket.
MX3863
10. Remove spacer (I) located between fixed idler assembly plates and carefully pull belt from assembly.
MX3866
11. Loosen two belt guides (J) and rotate away from left sprocket.
12. Remove timing belt, replace if necessary.
NOTE: The position of the drain holes in the spindle sheave (A) and the indentations in the timing sprocket (M) are in alignment with the mower blades (K) and (L).
MX0236
13. Position mower blades (K) and (L) 90° from each other.
IMPORTANT: Avoid damage! Handle timing belts with care. · DO NOT crimp. · DO NOT fold. · DO NOT twist. |
M92926a M92927a
MX3866
14. Install new mower deck timing belt:
a. Route belt around right spindle sprocket (N) located under the mower drive belt sheave.
MX3863
b. Route belt around outside of idlers and then in between the fixed idlers (O), pulling a belt loop through the idler assembly.
c. Insert spacer (I) between fixed idler plates and idlers.
Cummins ntc 350 diesel engine rebuild manual. d. Install the fixed idler assembly on the stud of the left support plate as you wrap belt loop around left spindle sprocket (P).
MX3866
15. Install washer and center nut (G) on fixed idler assembly. Leave nut loose at this time.
MX0236
16. Check that blades (K) and (L) are 90° from each other.
IMPORTANT: Avoid damage! Incorrect belt tensioning can cause belt damage. DO NOT over tighten belt tensioning spring assembly. |
MX0234
17. Install tensioning spring assembly and adjust timing belt tension:
a. Align notch (Q) in idler assembly with tab on spring bushing (S).
b. Rotate adjusting nut (F) clockwise until the washer (R) makes solid contact with the surface of the spring bushing (S).
c. Turn adjusting nut an additional 1/2 turn to allow for new belt stretch. DO NOT over tighten.
d. Rotate right spindle sheave clockwise and observe that belt is riding properly in sprockets and idlers.
e. Tighten jam nut (E) against adjusting nut.
MX3867
18. Tighten center nut (G) to 73 N·m (54 lb-ft.).
19. Install top washer on top of center nut.
MX0235
20. Adjust belt guides:
IMPORTANT: Avoid damage! Check belt guide-to-sprocket rim clearance. Measuring clearance incorrectly can cause belt or blade damage. |
a. Hold a 1 mm (0.039 in.) shim/gage between belt guides and sprocket rim, location (T), and rotate belt guides (J) clockwise against gage.
b. Tighten belt guide nuts to 24 N·m (18 lb-ft.).
MX3861
Picture Note: Right spindle sheave removed for photo clarity.
c. Remove gage. Clearance (T), one on each side, should be 1contact belt guide.
MX5358
21. Install timing belt cover (B) and fasten with five nuts (A). Tighten nuts to 14 N·m (10 lb-ft.).
22. Install mower drive belt.
23. Install mower and adjust mower engagement rod, if necessary.
1. Park tractor safely. Allow engine and muffler to cool completely.
2. Remove mower deck.
AMA10306_1
3. Remove six cap screws (A) and left and right belt shields.
AMA10306_2
4. Loosen sheaves (B) and (C).
5. Remove mower belt.
6. Clean top of mower deck and sheaves.
7. Inspect belt for wear or damage; replace as necessary.
8. Install belt on mower deck as shown.
9. Tighten sheaves.
10. Install belt shields and fasten with six cap screws.
http://peitbm.xtgem.com/Blog/__xtblog_entry/18987082-cyberbyte-antivirus-and-internet-security-premium-3-0-5-0#xt_blog. 11. Install mower deck and adjust mower engagement rod, if necessary.
12. Move lift lever to transport position.
NOTE: This procedure applies only to the 38-Inch and 48C mowers.
The Freedom42 mower has a self-adjusting spindle brake assembly - no adjustment is necessary.
| c CAUTION: Avoid injury! Rotating blades are dangerous. Mower blades must stop within 5 seconds after mower is turned off. Check spindle brake measurement every 25 hours or once a year (whichever comes first). |
1. Park tractor safely.
Money pro 2 0 7. 2. Adjust mower cutting height to 25 mm (1 in.).
3. Put lift lever in the mowing position.
4. Push mower engagement lever forward.
5. Remove belt shields.
BRAKEADJ
Macfamilytree 9 0 10 0. Picture Note: 38-Inch deck used for illustration.
6. Measure distance between brake pad surface (A) and pulley braking surface (B). Brake to pulley distance should be:
MIF
AMA10306_2
7. Turn adjusting nuts (E) on end of brake rods in correct direction to set brakes at proper distance from pulleys.
8. Install belt shields.
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
1. Park machine safely. (See Parking Safely in the Safety Section).
M32847
2. Put lift lever in mowing position.
3. Measure distance between blade tip and flat ground surface.
4. Turn blade. Measure distance between other blade tip and flat ground surface.
5. Install new blade, if the difference between the two measurements is more than 3 mm (1/8 in).
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
1. Raise mower deck to gain access to mower blades. If necessary, remove mower deck after allowing engine and muffler to cool completely.
2. Block mower blade with a piece of wood to prevent it from spinning.
M88119a
3. Loosen and remove cap screw (A), hardened washer (B), blade washer (C) and blade (D).
4. Inspect blades; sharpen, balance or replace blades as necessary.
1. Lubricate cap screw threads lightly with a general purpose grease or oil. This lubrication is to prevent rusting and seizing.
MIF
2. Position mower blade (D) with the cutting edge towards the ground onto the mower spindle.
3. Install blade washer (C) with cup side toward the blade.
4. Install hardened washer (B).
5. Install and hand tighten cap screw (A) until mower blade is in full contact (fully seated) with spindle.
6. Block mower blade with a piece of wood to prevent spinning and tighten cap screws to 53 N·m (39 lb-ft.).
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
1. Hold mower blade with glove to prevent mower blades from spinning.
2. Raise mower deck to gain access to mower blades. If necessary, remove mower deck.
MIF
3. Loosen and remove bolt with washer (A), and blade (B).
4. Inspect blades; sharpen, balance or replace blades as necessary.
1. Check mower to be sure you are installing the blades on the correct side:
P000151
· The RIGHT and LEFT sides are marked on the rear draft brackets (C).
MX0238
· There are direction arrows located on each outside edge of the mower. There is a RIGHT and a LEFT side blade. The blades are marked for identification.
MIF
2. Position mower blades (B) with the cutting edge towards the ground onto the mower spindle and align key on bottom of spindle with slot in blade.
IMPORTANT: Avoid damage! Improperly installed blades can loosen during operation. Do not lubricate or use power tools when installing the blade bolt or the bolt will be ineffective. Use a hand torque wrench and tighten bolts to blade bolt torque of: 57 N·m (42 lb-ft.) |
3. Install and hand tighten bolt with washer (A) until mower blade is in full contact (fully seated) with spindle.
4. Hold mower blade with glove to prevent spinning, tighten bolts to 57 N·m (42 lb-ft.).
5. Check mower deck timing and adjust if necessary.
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
1. Raise mower deck to gain access to mower blades. If necessary, remove mower deck.
2. Block mower blade with a piece of wood to prevent it from spinning.
M74256a
3. Loosen and remove bolt (A), washer (B) and blade (C).
4. Inspect blades; sharpen, balance or replace blades as necessary.
M74256a
1. Check that deflector cup (D) is in place between spindle and blade.
2. Position mower blade (C) with the cutting edge towards the ground onto the mower spindle.
3. Install blade washer (B) with cup side toward the blade.
4. Install and hand tighten bolt (A) until mower blade is in full contact (fully seated) with spindle.
5. Block mower blade with a piece of wood to prevent spinning and tighten cap screw to 68 N·m (50 lb-ft.).
| c CAUTION: Avoid injury! Mower blades are dangerous! · Always wear gloves while working on blades. · Always wear safety eye protection when grinding. |
Sharpen blades with grinder, hand file, or electric blade sharpener.
MIF
Keep original bevel (A) when grinding.
Blade should have 0.40 mm (1/64 in.) cutting edge (B) or less.
Balance blades before installing.
| c CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. |
1. Clean blade.
M61524
2. Put blade on nail in a vise. Turn blade to horizontal position.
3. Check balance. If blade is not balanced, heavy end of blade will drop.
4. Grind bevel of heavy end. Do not change blade bevel.
The technical manual contains service and repair instructions, special instructions, service and any additional information for quality service tractors John Deere X300.
This manual contains detailed electrical and hydraulic diagrams, which help to get a detailed description of all systems tractors, using which the user can determine where to install spare parts, etc.
Using this manual you can quickly and easily perform calibration special equipment to troubleshoot it and fix hardware problems and solve any problems that arise, to find information about the equipment.
The technical manual comes in PDF format. To view the information you must have any PDF Reader. Working with this manual, you can easily copy, save, and print the information you need. If necessary, you can print pages, pictures, charts, or the entire manual completely.
Contents:
Safety
Specifications and Information
Engine (FH491)
Engine (FH661 and FH721)
Engine - (FS541V)
Electrical
Power Train
Hydraulics
Steering
Attachments
Miscellaneous
0 
Star